Spectral radiance reconstruction from trichromatic camera responses based on orthogonal test and regularized algorithm

Reconstruction of spectral information based on multi‐channel image system is a significant problem in color reproduction, detection, and recognition. A spectral radiance reconstruction from trichromatic digital camera responses is researched in this article. The mapping relationship between the trichromatic imaging system response and the incident spectral radiance is analyzed. Then, in order to remove the ill‐posedness of the problem, a regularized constraint solution model of spectral radiance reconstruction matrix is established. And the spectral radiance can be reconstructed by spectral radiance reconstruction matrices and trichromatic imaging system response. Finally, the spectral radiance reconstruction matrix is estimated by the system radiometric calibration experiment. The input radiance is offered by a LCD display. A 3‐factor and 9‐level orthogonal test is designed for the calibration experiment, and a test set of 24 colors is used for precision analysis. The results show that the average relative mean error of our method is 8.69%, it is lower than that of Wiener filtering method by 2.84%. The method can reconstruct spectral radiance information effectively.     

Dual effect synergistically triggered Ce:(Y,Tb)3(Al,Mn)5O12 transparent ceramics enabling a high color-rendering index and excellent thermal stability for white LEDs

Ce:Y₃Al₅O₁₂ transparent ceramics (TCs) with appropriate emission light proportion and high thermal stability are significant to construct white light emitting diode devices with excellent chromaticity parameters. In this work, strategies of controlling crystal-field splitting around Ce³⁺ ion and doping orange-red emitting ion, were adopted to fabricate Ce:(Y,Tb)₃(Al,Mn)₅O₁₂ TCs via vacuum sintering technique. Notably, 85.4 % of the room-temperature luminescence intensity of the TC was retained at 150 °C, and the color rendering index was as high as 79.8. Furthermore, a 12 nm red shift and a 16.2 % increase of full width at half maximum were achieved owing to the synergistic effects of Tb³⁺ and Mn²⁺ ions. By combining TCs with a 460 nm blue chip, a warm white light with a low correlated color temperature of 4155 K was acquired. Meanwhile, the action mechanism of Tb³⁺ ion and the energy transfer between Ce³⁺ and Mn²⁺ ions were verified in prepared TCs.     

虚实结合的可穿戴产品适合性检验研究

目的 为了更科学地研究和检验可穿戴产品的适合性,提出一种适合性检验方法,能够精确保留现实环境中的产品佩戴关系,并能将现实与虚拟的适合性检验研究相结合,得到合理的适合性检验结果.方法 以虚拟现实眼镜的适合性检验为例,通过高精度的三维测量技术将现实环境中的人、产品以及人—产品佩戴关系转化为三维虚拟信息,并以人—产品佩戴三维模型为参考基准对齐人和产品的虚拟模型,得到保留现实佩戴关系的人—产品佩戴模型组,再应用偏差分析法得出人—机佩戴区域的可视化适合性结果和统计数据,结合主观评价方法进一步分析产品的适合性.结论 虚实结合的产品适合性检验方法可在虚拟环境中高精度地保留现实环境中的人—产品佩戴关系,并能得到可视化的适合性检验结果,为检验和指导产品的适合性提供依据.     

Enhancement of process modelling and simulation evaluation by deploying a test for assessment and feedback individualisation

This paper demonstrates a novel approach for a computer-based course assessment. A test is introduced in which computers are deployed. This significantly contributes to the enhancement of the marking consistency, individual performance distinction and feedbacks, and widen the questions range for computer-based modules. The proposed test method, for the first time, uses the simulation files marking for individualised evaluation purposes. The methodology has successfully been implemented in practice for three modules including Process Simulation (CE2105), Advanced Process Simulation (CE4023), and Process Computation (CE3021) at Aston University (UK) over three academic years, from 2016 to 2019. The effectiveness of the proposed approach has been evaluated using several factors, including final marks, consistency multiple academic years, and mark distribution. In contrast to the common teamwork assessments, individualised feedback became possible. While ASPEN has been used for CE4023 and CE2105 tests, MATLAB has been applied as the computation platform for CE3021 module. This reveals the applicability of different software in proposed methodology. The number of students in the cohorts studied was from 52 to 204, demonstrating the applicability of the method for various cohort sizes. Even though the methodology has been demonstrated based on the chemical engineering discipline modules, it allows digitalising the delivery and assessment of a wide range of simulation techniques in many disciplines.     

Stress field and damage evolution in C/SiC woven composites: Image-based finite element analysis and in situ X-ray computed tomography tests

The construction and examination of meso-structural finite element models of a Chemical-Vapor-Infiltrated (CVI) C/SiC composite is carried out based on X-ray microtomography digital images (IB-FEM). The accurate meso-structural features of the C/SiC composites, which are consisted of carbon fiber tows and CVI-SiC matrix, in particular the cavity defects, are reconstructed. With the IB-FEM, the damage evolution and fracture behaviors of the C/SiC composite are investigated. At the same time, an in situ tensile test is applied to the C/SiC composite under a CT real-time quantitative imaging system, aiming to investigate the damage and failure features of the material as well as to verify the IB-FEM. The IB-FEM results indicate that material damage initially occur at the defects, followed by propagating toward the fiber-tow/SiC-matrix interfaces, ultimately, combined into macro-cracks, which is in good agreement with the in situ CT experiment results.     

一种磁控管用扼流线圈仿真设计

采用电路仿真软件仿真滤波组件S参数曲线,观察曲线随器件参数的变化;介绍利用三维全波电磁仿真软件HFSS简化设计流程的方法,并与测试结果对比。结果表明:利用3D仿真软件在满足器件设计精度的同时可以简化线圈的设计流程。     

Preparation and electrochemical characterization of Ti-based amorphous metallic glass with high strength

Ti-based amorphous metallic glasses have excellent mechanical, physical, and chemical properties, which is an important development direction and research hotspot of metal composite reinforcement. As a stable, simple, efficient, and large-scale preparation technology of metallic powders, the gas atomization process provides an effective way of preparing amorphous metallic glasses. In this study, the controllable fabrication of a Ti-based amorphous powder, with high efficiency, has been realized by using gas atomization. The scanning electron microscope, energy-dispersive spectrometer, and X-ray diffraction are used to analyze surface morphology, element distribution, and phase structure, respectively. A microhardness tester is used to measure the mechanical property. An electrochemical workstation is used to characterize corrosion behavior. The results show that as-prepared microparticles are more uniform and exhibit good amorphous characteristics. The mechanical test shows that the hardness of amorphous powder is significantly increased as compared with that before preparation, which has the prospect of being an important part of engineering reinforced materials. Further electrochemical measurement shows that the corrosion resistance of the as-prepared sample is also significantly improved. This study has laid a solid foundation for expanding applications of Ti-based metallic glasses, especially in heavy-duty and corrosive domains.     

Reduced‐scale test to assess the effect of fire barriers on the flaming combustion of cored composites: An upholstery‐material case study

Herein, we describe a reduced‐scale test (“Cube” test), measuring the fire performance of specimens including a fire barrier (FB) and a flammable core material, which acts as the main fuel load. The specimen is intended to reproduce a cross‐section of a composite product where heat/mass transfer occurs primarily in a direction perpendicular to the FB. The Cube test procedure and benefits are discussed in this work by adopting residential upholstery furniture as an exemplary study. One flexible polyurethane foam, one polypropylene cover fabric, and 10 commercially available FBs were selected. They were used to compare the fire performance of FBs, measured in terms of peak of heat release rate, in the ASTM E1474‐14 standard test and the newly developed Cube test. Edge effects severely affected the performance of FBs in the ASTM E1474‐14 standard test but not in the Cube test. Furthermore, appropriate test conditions were determined in the Cube test to measure the so‐called “wetting point,” that is, the time and value of heat release rate measured when flammable liquid products were first observed on the bottom of the specimen. The relevance of the “wetting point” in terms of full‐scale fire performance and failure mechanism of FBs is discussed.